WallStack

CMU Block Wall Calculator

Wall dimensions

Wall length

ft
in

Wall height

ft
in

From the top of the footing to the top of the wall.

%
blocks

Ask your supplier — 72, 90 and 108 are all common.

Materials

wall blocks95
mortar mix (80 lb bags)8bags
crushed stone base, compacted0.77cu yd

Cut list

Masonry

  • 95wall blocksor 2 x 90-block pallet
  • 8 bagsmortar mix (80 lb bags)

Stone and gravel

  • 0.77 cu ydcrushed stone base, compactedbuy 1.14 tons, or 42 x 0.5 cu ft bag

Cuts to make on site

  • Cut 3 blocks in half (running bond: every second course starts and ends with a half block)
Calculation steps
  1. Coursesceil(48 in / 8 in)6 courses
  2. wall blocksceil(240 in / 16 in) x 6 courses + 5% waste95 blocks
  3. mortar mix (80 lb bags)ceil(90 blocks / 12 per bag)8 bags
  4. crushed stone base, compacted240 in x 19.625 in x 6 in x 125% compaction0.77 cu yd

Concrete block, cinder block and CMU all mean the same unit, and this calculator handles all three. Enter the wall length and height, choose the block size, and get the blocks, half blocks to cut, mortar bags, caps and base gravel as a cut list. If the wall holds back soil, it adds the drainage stone, drain pipe and filter fabric too.

How the quantities are worked out

Block sizes are the actual sizes: a nominal 8 x 8 x 16 in. block measures 7 5/8 x 7 5/8 x 15 5/8 in. and lays out to 8 x 16 in. with a 3/8 in. mortar joint. Blocks are counted per course and per wall length, a running bond adds half blocks at the ends of every second course, and your waste allowance is added before rounding up.

Mortar is counted at 12 standard blocks per 80 lb bag of Type S mortar mix, on the blocks you actually lay. The base under the wall is estimated as a 6 in. compacted gravel bed; a mortared block wall normally sits on a poured concrete footing, which this calculator does not size.

Walls that hold back soil

Turn on the option for a wall that holds back soil to add a drainage column of clean stone behind the wall, a 4 in. perforated drain pipe with outlets at least every 50 ft, and filter fabric over the stone. A mortared block wall that retains soil also needs steel reinforcement and grout designed for the load. That is engineering work, not a materials count, so it is not included.

Frequently asked questions

What is the difference between cinder block, concrete block and CMU?

Today they are the same thing. CMU stands for concrete masonry unit, the trade name for a hollow concrete block. Decades ago some blocks were made with coal cinders as the aggregate, and the name cinder block stuck even though modern blocks use sand and gravel. A standard 8 x 8 x 16 in. block actually measures 7 5/8 x 7 5/8 x 15 5/8 in., so that it lays out to 8 x 16 in. with a 3/8 in. mortar joint.

How many concrete blocks do I need per square foot?

A standard 8 x 16 in. block covers 8 x 16 = 128 sq in. of wall face including its mortar joint, which works out to 1.125 blocks per square foot. Multiply by the wall area and add a waste allowance; the calculator does this by counting whole blocks per course and whole courses, which is more accurate for short or oddly sized walls.

How many blocks does one bag of mortar lay?

Mortar mix manufacturers rate an 80 lb bag of Type S mortar at about 12 standard 8 x 8 x 16 in. blocks. The calculator divides the number of blocks you will actually lay by 12 and rounds up to whole bags. Mortar use varies with the joint size and how much falls off the trowel, so it is worth buying a bag more than the count.

Why does the cut list tell me to cut blocks in half?

In a running bond each course is shifted half a block from the one below, so the vertical joints never line up. That means every second course starts and ends with a half block. The cut list counts those halves for you. You can use a masonry saw, or buy half blocks if your supplier stocks them.

Does a block wall that holds back soil need drainage?

Yes. Turn on the option for a wall that holds back soil and the calculator adds drainage stone, a perforated drain pipe and filter fabric behind the wall. A mortared block wall that retains soil also needs steel reinforcement and a footing sized for the load, which this calculator does not design; walls over 4 ft from the bottom of the footing, or walls with a driveway or slope above them, usually need a permit and a design by a licensed engineer.